£41.99

 

 Raspberry Pi - I2C 16 Channel PWM Servo & L293D-2 4 & DC Power Motor Board

  

Raspberry Pi - I2C 16 channel PWM Servo & L293D x2            4 Motor & DC Power Board

Support Rs-Pi V2 P5 get extra 4 GPIO(28,29,30,31)

 

  

                                                      

   This board use   RS-Pi GPIO  17,18,27,22,23,24,25,4 

  GPIO 17,18,27,22   for MA1, MB1

  GPIO 23,24,25,4 for MA2, MB2

GPIO 28 ~31  (need V2 - P5 connector) for ultrasonic sensor connector (2GPIO , one for Trig, one for Echo) or other devices

2 extra 12c input for sensors  (5V or 3v3) (5V port with Level converter)

switch S1 TO S5 ( use GPIO 7,8,9,10,11 signal)  (SPI signal)

 

LM2596S  STEP DOWN POWER MODULE

Input voltage range: DC 7.2V to 12V (input voltage must be higher than the output voltage above 1.5V. Could not boost)

Output voltage range: DC voltage from 5V to 10V continuously adjustable, high efficiency (92%) of the maximum output current of 2A.

PCA9685

The PCA9685 is an I2C-bus controlled 16-channel LED controller optimized for LCD
Red/Green/Blue/Amber (RGBA) color backlighting applications. Each LED output has its
own 12-bit resolution (4096 steps) fixed frequency individual PWM controller that operates
at a programmable frequency from a typical of 40 Hz to 1000 Hz with a duty cycle that is
adjustable from 0 % to 100 % to allow the LED to be set to a specific brightness value.
All outputs are set to the same PWM frequency.

PCA9685 also has a built-in oscillator for the PWM control.
However, the frequency used for PWM control in the PCA9685 is adjustable from
about 40 Hz to 1000 Hz as compared to the typical 97.6 kHz frequency of the
PCA9635. This allows the use of PCA9685 with external power supply controllers. All
bits are set at the same frequency.

The PCA9685 has 4096 steps (12-bit PWM)         

 

           Rs-Pi- 16channel PWM & 4 Motor Power Board plug in Raspberry Pi        

 

Support our Pi_Scratch software   Detail

(1) Servo Motor control

 
2 Servo in  channel 0 & channel 7 
 
   Command "SE"+ "PWM (0-15)" + "a" +"angle"  for Address 41
 
    se7a10   --> channel 7 servo move 10 angle  address 41
    se7a-10  --> channel 7 servo move -10 angle address 41
    se0a10   --> channel 0 servo move 10 angle  address 41
    se0a-10  --> channel 0 servo move -10 angle  address 41

 

(2) PWM  LED output demo

 

  
 LED module (Blue, Green,Yellow,Red)

 

LED Scrolling  Command     PWMLED41S0E15D4True
PWMLED”Address” S[Start channel] E[End channel] D[Delay / Timing] [True/False]
 
Address 40, 41, 42, 43, 44 
Start channel & End channel   0 ~ 15    16 channel
D   1,2,3,4,5    (1 ~ 100) Delay Timing
 
LED Brightness control Command 
PWMLED “Address” “B” “0 ~ 1000“ 
PWMLED41B1000
 
 Stop command 
"PWMLED41STOP"

 

 

   Test Program

servo-41.py    pwm   

pwm-v2  for Raspberry Pi V2 board

2motor.py  4motor.py

User Manual

 

Package Content

  1x Rs-Pi I2C 9685 -16 channel PWM &  L293D  4 Motor & DC Power board

1x manual 

  

 
 

Raspberry Pi

iPad  iPhone

Products  

 

Copyright ?009
www.pridopia.co.uk
All rights reserved

Home           About us           Support           Shopping           Contacts            FAQ